VW Touareg repair


+ 1. Operation and car maintenance
- 2. Engine
   + Preliminary checks on the car
   - Mechanical part (petrol engines 3,2L)
      Removal of the power unit
      Removal and installation of the left and right pillows of a support of the engine
      Removal and installation of a conducted disk
      Removal and epiploon installation from a flywheel
      Replacement of an epiploon of a cranked shaft on the party of a damper of krutilny fluctuations
      Replacement of a sealing flange of a cranked shaft on the party of a damper of krutilny fluctuations
      Removal and installation of a cranked shaft
      Removal and installation of a lateral cover
      Removal and installation of a cover of a head of the block of cylinders
      Removal and installation of a head of the block of cylinders
      Check of phases of a gazoraspredeleniye
      Adjustment of phases of a gazoraspredeleniye
      Removal of cam-shafts
      Installation of cam-shafts
      Check of axial shift of cam-shafts
      Marking of cam-shafts
      Replacement of maslosjemny caps
      Check of directing plugs of valves
      Processing of saddles of valves
      Sizes of valves
      Check of pistons, piston rings and diameter of the cylinder
   + Mechanical part (petrol engines 4,2L)
   + Mechanical part (diesel engines 5,0L)
   + Removal and stretcher installation
   + pressurization System (diesel engines)
   + cooling System (petrol engines)
   + cooling System (diesel engines)
   + greasing System (petrol engines)
   + greasing System (diesel engines)
   + injection System (petrol engines)
   + injection System (diesel engines)
   + System of production of the fulfilled gases
   + System топливоподачи (beninovy engines)
   + Tables
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes



Volkswagen Touareg / Touareg repair>> Engine>> Mechanical part (petrol engines 3,2L)>> Replacement of a sealing flange of a cranked shaft on the party of a damper of krutilny fluctuations
Removal
Bring a radiator frame into service situation.
Remove poliklinovy a belt.
Remove a damper of krutilny fluctuations. For this purpose fix a damper of krutilny fluctuations by means of a key for T10069 fixing.
To remove the oil pallet.
Turn off fastening of a sealing flange.
Remove the hermetic remains from sealing surfaces.

Installation
Remove the oil remains on a shatunny neck of a cranked shaft by means of pure rags.
Cut off a tube nouse on a forward mark (to opening O about 3 mm).

Fig. 2.50 . Scheme of drawing of hermetic


Put a hermetic layer in thickness about 2-3 mm, as is shown in drawing 2.50 , on a pure sealing surface of a flange.

NOTE
Before drawing of hermetic cover an epiploon with pure rags.
The layer of hermetic should be not thicker than 2-3 mm, otherwise superfluous hermetic can get to the oil pallet and litter the mesh filter in a maslozaborny branch pipe.
Observe a hermetic expiration date.
The sealing flange should be established during 5 mines after drawing of silicone hermetic.

Establish directing T10215/1 plug 1 in front on a crankshaft 3 neck.

Fig. 2.51 . Installation of a sealing flange with an epiploon


Then accurately establish a sealing flange with an epiploon 2-via directing plug (fig. 2.51) .
Fasten a flange to the block of cylinders.
Establish the oil pallet.

NOTE
It is necessary to replace a fixing bolt of a damper of krutilny fluctuations.

Tighten a fixing bolt by means of a dinamometrichesky key of V.A.G 1601.
Establish a damper of krutilny fluctuations and fix it T10069 countersupport.
Tighten a new fixing bolt the moment of 100 N · m + 1/4 turns (90 °).
Establish poliklinovy a belt.



<