VW Touareg repair


+ 1. Operation and car maintenance
- 2. Engine
   + Preliminary checks on the car
   + Mechanical part (petrol engines 3,2L)
   + Mechanical part (petrol engines 4,2L)
   + Mechanical part (diesel engines 5,0L)
   + Removal and stretcher installation
   + pressurization System (diesel engines)
   + cooling System (petrol engines)
   + cooling System (diesel engines)
   + greasing System (petrol engines)
   + greasing System (diesel engines)
   + injection System (petrol engines)
   + injection System (diesel engines)
   + System of production of the fulfilled gases
   - System топливоподачи (beninovy engines)
      Replacement of the fuel filter
      Fuel pumping from a tank
      Removal and installation of the module of supply of fuel, fuel level sensor and ezhektsionny pumps
      Check of power supply of pumps
      Electronic regulation of engine capacity (electronic drive of an accelerator)
      Absorber with absorbent carbon (cars with an alphabetic reference of the AZZ, BKJ, BMV and BRJ engine)
      Absorber with absorbent carbon (cars with an alphabetic reference of the BAA and BMX engine)
   + Tables
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes



Volkswagen Touareg / Touareg repair>> Engine>> System топливоподачи (beninovy engines)>> Fuel pumping from a tank
Works order
Open the hatch of a mouth of a fuel tank.

Fig. 2.311 . Installation of adaptations for fuel pumping from a tank


Insert pumping-out hose device (fig. 2.311) for VAS 5190 fuel pumping approximately on 170–180 cm into a mouth of a fuel tank and to pump out fuel.

NOTE
If fuel ceases to be pumped out, the fuel tank is devastated so that the flange of the sensor can be safely open. With the fuel remains the tank can be removed.

In need of works with fuel pumps and sensors execute the following operations:

Fig. 2.309 . Nuts of fastening of a cover


Cut a carpet from points And to points In in in advance made an incision place (fig. 2.309) .
Turn off nuts of 1 fastening of a cover. In case of need turn off fastening of a support of an armrest 2 or a basic arm.
To a branch pipe for connection submitting топливопровода and топливопровода an additional heater enclose rags and disconnect a hose.

NOTE
For this purpose press the button on the connecting coupling.

Disconnect the tip of the fuel pump and the fuel level sensor.

Fig. 2.312 . Untwisting of a lock ring


Turn off a lock ring by means of T10202 key from a sensor flange (fig. 2.312) .
Accurately raise a sensor flange.
Insert pumping-out hose of the device for VAS 5190 fuel pumping as it is possible more deeply in the right and left parts of a fuel tank and pump out fuel.
At works on the left side of a tank follow the instructions provided above.

Fig. 2.313 . The adaptation for a detachment of ventilating tubes


At a detachment of ventilating tubes of the button of connecting couplings of hoses can not be pressed. Thus use the T10118 replacement tool (fig. 2.313) .
At further works with internal details of a fuel tank flanges of sensors can remain removed.
If it was necessary to merge only fuel from a tank, follows again establish flanges of sensors.
Before installation check sealing rings of flanges on landing density.

NOTE
If sealing rings were blown up because of fuel influence, it is necessary to replace them.


Fig. 2.314 . Direction of installation of flanges


Establish flanges of sensors with a fixing slip in the movement direction (fig. 2.314) .
Twirl lock rings on the right and at the left by means of T10202 key with the moment of 145 N · m.


<