VW Touareg repair


+ 1. Operation and car maintenance
+ 2. Engine
+ 3. Transmission
- 4. Running gear
   + Wheels and tires
   - Forward suspension bracket
      Stretcher, stabilizer, bottom lever of a suspension bracket
      Removal and stretcher installation
      The disconnected stabilizer
      Pumping of the disconnected stabilizer
      Suspension bracket of forward wheels
      Removal and installation of an amortization rack
      Removal and installation of the sensor of level of a body of G78/G289 on cars with amortization racks
      Wheel support
      Removal of a screw spring
      Installation of a screw spring
   + Back suspension bracket
   + Tables
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes


Volkswagen Touareg / Touareg repair>> Running gear>> Forward suspension bracket>> Stretcher, stabilizer, bottom lever of a suspension bracket
NOTE
If details with rezinometallichesky support were replaced or bolts and nuts on these details were weakened, before their inhaling the support of the corresponding wheel is necessary for bringing into situation when it is affected by own mass of the car.

Fig. 4.46 . The scheme of installation of knot – a stretcher, the stabilizer, the bottom lever of a suspension bracket: 1–forward main transfer; 2–stretcher; 3–самоконтрящаяся nut; 4–a bolt with a six-sided head; 5–a bolt with a six-sided head; 6–a bolt with a six-sided head; 7–самоконтрящаяся nut; 8–ekstsentrikovy washer; 9–ekstsentrikovy bolt; 10-a bolt with a six-sided head; 11-bottom lever of a suspension bracket; 12-самоконтрящаяся nut; 13-case of the bearing of a nave of a wheel; 14-the disconnected stabilizer; 15-stabilizer bearing; 16-bracket; 17-a bolt with a six-sided head; 18-stabilizer


Stretcher fixing
For performance of certain assembly operations removal of a stretcher or all forward suspension bracket is required. The initial provision of a stretcher concerning a body is possible fix by means of adaptations for T10300 fixing. The precondition for use of fixing adaptations are rezinometallichesky support with a round opening for a fixing bolt. At start of a mass production rezinometallichesky support with quadrangular openings were established, the provision of a stretcher with such support is not fixed. Directly ahead of lowering of a stretcher or all forward suspension bracket always to establish fixing adaptations. Upon termination of repair it is necessary execute a trial trip. If at rectilinear movement the wheel is not necessary directly, it is necessary execute RUUK.
Remove a noise isolation under an engine/transmission

Fig. 4.47 . Installation of cores in loops


Insert cores of 10-222 A/11 into loops of the shooter of an arm of the engine on the right and left parties (fig. 4.47) .

Fig. 4.48 . Installation of wooden whetstone


Insert wooden whetstone A in length about 300 mm into brackets of cores of 10-222 A/11 (fig. 4.48) .
Thus brackets should be directed back.
Tighten clips of cores, for this purpose wooden whetstones should lean on an arm of hinged units B.

Fig. 4.49 . Bolts of fastening of a stretcher


Remove bolts 2 (fig. 4.49) .

Fig. 4.50 . Adaptations for fixing


In these two points, "by hand", twist adaptations for T10300 fixing before B marking (fig. 4.50) .
Now tighten fixing adaptations the moment of 30 N · m, thus hold a sleeve from a provorachivaniye a rozhkovy wrench.
Now the provision of a stretcher is fixed.
Removal of fixing T10300 adaptations is carried out in return sequence.

Inhaling moments
Stretcher to a body: 120 N · m +180 °.


<