VW Touareg repair


+ 1. Operation and car maintenance
+ 2. Engine
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
- 8. Body
   - External elements of a body
      Removal and cowl installation
      Removal of a gas emphasis
      Production of gas from a gas emphasis
      Removal and isolation installation
      Removal and installation of the lock of a cowl
      Adjustment of the lock of a cowl
      Detachment of a flexible cable
      Removal and installation of a door of a luggage compartment
      Adjustment of a door of a luggage compartment with the hinge
      Adjustment of a loop of the lock
      Removal and installation of a cap of a gas emphasis
      Removal and installation of a cap of a gas emphasis
      Removal and installation of elements of locking and door unlocking
      Removal and installation of the lock of a door of a luggage compartment
      Removal and installation of a loop of the lock with a dovodchik
      Removal and installation of the electric motor of opening of a door of a luggage compartment
      Removal and installation of a back spoiler
      Removal and installation of elements of locking and unlocking of the hatch of a fuel tank
      Door adjustment
      Removal and installation of the case of the cylinder of the lock
      Removal and installation of the handle of a door
      Removal and installation of the lock of a door
      Adjustment of a back door
      Removal and installation of the case of the cylinder of the lock
      The elevating and movable hatch with the glass panel
      Removal of the glass panel of the elevating and movable hatch
      Check of a parallel course of the glass panel
      Adjustment of a sealant of the panel of the hatch
      Removal of the sun-protection screen
      Removal and installation of facing of a front bumper
      Removal and installation of facing of a rear bumper
+ electric equipment Schemes



Volkswagen Touareg / Touareg repair>> Body>> External elements of a body>> Removal and installation of the case of the cylinder of the lock

Fig. 8.27 . Handle and door lock: 1–door lock; 2–screw; 3–the fixing screw; 4–a bolt with an internal asterisk; 5–laying; 6–case of the cylinder of the lock; 7–key; 8–door handle; 9–laying; 10-wire of the sensor of a contact (kessy); 11-screw; 12-fastening; 13-cap; 14-flexible cable; 15-corner holder


Removal

Fig. 8.28 . Cap extraction


Hook a cap from the bottom opening of a, then pull a cap down b (fig. 8.28) .

Fig. 8.29 . Extraction of the case of the cylinder of the lock


Pull for the handle of a door 1 and hold it. Unscrew a bolt 3 by means of a face key of T 10072 against the stop. Thus you release the case of the cylinder of the lock 2 (fig. 8.29) .
If in the case of the cylinder of the lock there is no cylinder of the lock, you can take out the case of the cylinder of the lock 2 at right angle to a door from fastening of the door handle.
If in the case of the cylinder of the lock there is a lock cylinder, it is necessary to weaken fixing screw 3 so that it was possible to take out this case 2 at right angle from fastening of the door handle.

Installation
Insert the case of the cylinder of the lock at right angle into fastening of the door handle.
Now twirl a face key a bolt in fastening.
Distinct click testifies that the door handle was again fixed in the case of the cylinder of the lock.

NOTE
In an installation time the case of the cylinder of the lock should be pressed to an external covering of a door from the inside. The door handle is established on a door leaky.

Further installation is carried out in return sequence.
In summary it is necessary to check operation of the door handle and the lock as at the wrong adjustment and fixing of a flexible cable the door can not open.


<