VW Touareg repair


+ 1. Operation and car maintenance
+ 2. Engine
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
- 8. Body
   - External elements of a body
      Removal and cowl installation
      Removal of a gas emphasis
      Production of gas from a gas emphasis
      Removal and isolation installation
      Removal and installation of the lock of a cowl
      Adjustment of the lock of a cowl
      Detachment of a flexible cable
      Removal and installation of a door of a luggage compartment
      Adjustment of a door of a luggage compartment with the hinge
      Adjustment of a loop of the lock
      Removal and installation of a cap of a gas emphasis
      Removal and installation of a cap of a gas emphasis
      Removal and installation of elements of locking and door unlocking
      Removal and installation of the lock of a door of a luggage compartment
      Removal and installation of a loop of the lock with a dovodchik
      Removal and installation of the electric motor of opening of a door of a luggage compartment
      Removal and installation of a back spoiler
      Removal and installation of elements of locking and unlocking of the hatch of a fuel tank
      Door adjustment
      Removal and installation of the case of the cylinder of the lock
      Removal and installation of the handle of a door
      Removal and installation of the lock of a door
      Adjustment of a back door
      Removal and installation of the case of the cylinder of the lock
      The elevating and movable hatch with the glass panel
      Removal of the glass panel of the elevating and movable hatch
      Check of a parallel course of the glass panel
      Adjustment of a sealant of the panel of the hatch
      Removal of the sun-protection screen
      Removal and installation of facing of a front bumper
      Removal and installation of facing of a rear bumper
+ electric equipment Schemes


Volkswagen Touareg / Touareg repair>> Body>> External elements of a body>> Removal of the glass panel of the elevating and movable hatch
Lift the hatch.
Shift the sun-protection screen back.
Release the goffered cover from the bottom level, beginning from a back part of the hatch.
Then release the goffered cover from the top level, beginning from a forward part of the hatch.

Fig. 8.44 . Removal of the goffered cover


Pull the goffered cover from grooves back and remove its (fig. 8.44) .
Unscrew fixing screws (on three on each party) 4,5 N · m.

Fig. 8.45 . Removal of the glass panel


Remove the glass panel of the elevating and movable hatch, having lifted it up (fig. 8.45) .

NOTE
At the removed glass panel to open the hatch in situation «geцffnet/it is open» it is forbidden, as the glass panel will not press water taking away fillet which because of it can get stuck.

Installation of the glass panel of the elevating and movable hatch
The panel should be established in a starting position (the panel of the hatch is closed)

Starting position

Fig. 8.46 . Marking for hatch installation in a starting position


Marking on the top part directing, behind, 1 should be on both parties between marks an on kulisny directing 2 (fig. 8.46) .
Kulisny directing 2 it should be fixed in a directing rail (by hand does not move).
If it not so, adjust a parallel course.
Insert the panel of the elevating and movable hatch from above and twirl screws (scenes / cover) (fig. 8.45) .
Do not tighten screws too strongly.

NOTE
Tighten screws after panel adjustment on height with the moment of an inhaling of 4,5 N · m.

Adjustment of the glass panel of the elevating and movable hatch (adjustment on height)
The starting position of the elevating and movable hatch should be correct.
Lift the glass panel.
Shift the sun-protection screen back.
Release the goffered cover from the bottom level, beginning from a back part of the hatch (fig. 8.44) .
Then release the goffered cover from the top level, beginning from a forward part of the hatch.
Extend the goffered cover back from grooves and remove it.
Bring the glass panel into a starting position.
Execute adjustment of the glass panel of the hatch on height in front and behind according to drawings to avoid when driving extraneous noise.
Panel adjustment in front:
a= 0–1 mm are lower than the roof plane
Arrow – the movement direction
Panel adjustment behind:
b= 0–1 mm are higher than the roof plane
Arrow – the movement direction
Tighten screws of the glass panel with the moment of an inhaling of 4,5 N · m.

Fig. 8.47 . Scheme of adjustment of the panel in front



Fig. 8.48 . Scheme of adjustment of the panel behind




<