VW Touareg repair+ 1. Operation and car maintenance - 2. Engine + Preliminary checks on the car + Mechanical part (petrol engines 3,2L) + Mechanical part (petrol engines 4,2L) + Mechanical part (diesel engines 5,0L) - Removal and stretcher installation Removal and installation of pillows and engine support (right and left) Removal and installation of a conducted disk Removal and installation of a stage of support of a cranked shaft Forward sealing laying of a flange and damper of krutilny fluctuations Replacement of an epiploon of a cranked shaft on the party of a damper of krutilny fluctuations Replacement of an epiploon of a cranked shaft on the party of the mechanism of a gazoraspredeleniye of the engine Replacement of an epiploon of a shaft of a drive of the generator Installation of a cover of the distributive mechanism Removal and installation of a leading gear wheel of a camshaft Check of phases of a gazoraspredeleniye Adjustment of phases of a gazoraspredeleniye Removal and installation of heads of the block of cylinders Removal and installation of covers and laying of heads of the block of cylinders Repair of heads of the block of cylinders + pressurization System (diesel engines) + cooling System (petrol engines) + cooling System (diesel engines) + greasing System (petrol engines) + greasing System (diesel engines) + injection System (petrol engines) + injection System (diesel engines) + System of production of the fulfilled gases + System топливоподачи (beninovy engines) + Tables + 3. Transmission + 4. Running gear + 5. Steering mechanism + 6. Brake system + 7. Onboard electric equipment + 8. Body + electric equipment Schemes |
Volkswagen Touareg / Touareg repair>> Engine>> Removal and stretcher installation>> Adjustment of phases of a gazoraspredeleniye
Works order
Dismantle the engine and a transmission.
Dismantle the fuel pump and the pump of tandemny type from heads of the block of cylinders.
Remove sound insulation and casings from heads of the block of cylinders.
Remove a sound-proof cover and a cover of a head of the block of cylinders.
Rotate the engine by means of T10172 countersupport while at least one stopper of a camshaft will not be established.
Establish on a gear wheel of the fixed camshaft the tightening T10199 adaptation and will twist a bolt of a gear wheel of a camshaft. Now the gear wheel freely rotates on a camshaft
(fig. 2.197)
.
If only one stopper of a camshaft was established:
Rotate an engine shaft by means of T10172 countersupport while the clamp of a camshaft of other number of cylinders will not be established.
Establish the tightening T10199 adaptation on a gear wheel of a camshaft and Turn off a gear wheel bolt. Now the gear wheel freely rotates on a camshaft.
Remove a damper of krutilny fluctuations. Use T10172 countersupport with T10172/1 bolts.
Fasten a stopper of a cranked shaft of T10195 to an end face of a cranked shaft. Thus watch the provision of an adjusting pin
(fig. 2.199)
.
After that carefully rotate a cranked shaft while the ledge of a stopper of a cranked shaft of T10195 will not get to calibration openings.
Establish T10199/1 clip how it is shown in
drawing 2.199
, and tighten tightening bolts of the tool with the moment of 70 N · m.
Establish a dinamometrichesky key (40–200 N · м) V. A. G 1332 in a tetrahedron of the tightening tool also press with effort of 80 N · m against the direction of rotation of a shaft of the engine to eliminate люфт a tooth gearing
(fig. 2.200)
.
Number of cylinders 1: in the arrow direction.
Number of cylinders 2: against the arrow direction.
Without weakening pressure, tighten fixing bolts of a gear wheel of a camshaft by means of a face nozzle of T10198 since the moments of 50 N · m.
Remove the tightening T10199/1 adaptation.
Establish the tightening adaptation – T10199 on a camshaft gear wheel.
|
< |