Removal of a cover of a nave

Take a wire stripper from the onboard tool.

Fig. 1.139 . Removal of a cover of a nave

Hook on a wire stripper for a cover (fig. 1.139)

Extend a cover.

The wire stripper enters into a set of the onboard tool.

Removal of caps of wheel bolts

Fig. 1.140 . Removal of caps of wheel bolts

Insert the end of a wire stripper into a cap opening (fig. 1.140) .

Remove a cap.

Caps serve for protection of wheel bolts, and after change of a wheel they should be put on back.

Weakening of wheel bolts

Fig. 1.141 . Weakening of wheel bolts

Pull a wheel key against the stop over a bolt (fig. 1.141) .

Undertake for the end of a wheel key and turn a key approximately on one turn counter-clockwise.

Fig. 1.142 . Wheel bolt-sekretka and adapter

Take an adapter for bolts-sekretok from a set of the onboard tool 2 (fig. 1.142) .

Insert an adapter against the stop into a bolt-sekretku 1.

Pull a wheel key against the stop over an adapter 2.

Undertake for the end of a wheel key and turn a key approximately on one turn counter-clockwise.

If to weaken a bolt it is not possible, it is possible to press for the key end a foot. Thus hold a body of the car and keep balance.

Car lifting

Fig. 1.143 . Places under a jack

Find a place for installation (fig. 1.143) of a jack which is about a replaced wheel.

Lift a jack paw so that it was possible to put still a jack under the car.

Check, whether completely there is a jack support on the earth.

Fig. 1.144 . The provision of a jack before lifting of the left back wheel

Amend situation of a jack and then evenly lift a jack paw until it will not clasp a vertical edge (fig. 1.144) from below the car.

Rotate the jack handle until the wheel will not come off the earth.

It is necessary to establish a jack only under intended for this place. About each wheel there is such place.

Wheel change

Fig. 1.145 . Wheel change: vyvertyvaniye of wheel bolts

Completely turn out the top wheel bolt a shestigrannik of a screw-driver and put it on a pure surface (fig. 1.145)

Fig. 1.146 . An assembly pin in the top opening

Screw an assembly pin (fig. 1.146) a hand in the released carving opening.

Turn out other wheel bolts.

Remove a wheel. Thus the assembly pin remains in an opening.

Installation of a harmonious spare wheel

Pull a spare wheel over a nave through an assembly pin. The harmonious spare wheel should be not beefy at installation.

Acquire wheel bolts and screw them by means of a shestigrannik of a screw-driver, having slightly tightened wheel bolts.

Turn out an assembly pin and screw the remained wheel bolt.

Pump up a spare wheel – pressure of air in it 3,5 bar.

Lower a jack the car.

Reliably tighten bolts a wheel key. Tighten bolts not around, but alternately opposite bolts.

Tires with the directed drawing of a protector

Wheels with such tires should be correctly put.

With the directed drawing of a protector the shooters specifying the direction of rotation of the tire have tires on боковине. It is necessary to provide the specified direction at installation of wheels on the car. All advantages of such tires concerning coupling with darling of wear, noise and hydroplaning are thus realized.

If the wheel is established so that rotates against arrows, move carefully as in this case the tire works not in the best way. It is especially shown at movement on a wet covering. completely to use all advantages of tires with the directed drawing of a protector, at the first possibility replace a wheel with another on which the tire has the correct situation.

After wheel change

Lay the removed wheel in a luggage compartment.

Whenever possible check an inhaling of wheel bolts a dinamometrichesky key rather.

As soon as possible repair or replace the removed wheel.