VW Touareg repair


+ 1. Operation and car maintenance
- 2. Engine
   + Preliminary checks on the car
   - Mechanical part (petrol engines 3,2L)
      Removal of the power unit
      Removal and installation of the left and right pillows of a support of the engine
      Removal and installation of a conducted disk
      Removal and epiploon installation from a flywheel
      Replacement of an epiploon of a cranked shaft on the party of a damper of krutilny fluctuations
      Replacement of a sealing flange of a cranked shaft on the party of a damper of krutilny fluctuations
      Removal and installation of a cranked shaft
      Removal and installation of a lateral cover
      Removal and installation of a cover of a head of the block of cylinders
      Removal and installation of a head of the block of cylinders
      Check of phases of a gazoraspredeleniye
      Adjustment of phases of a gazoraspredeleniye
      Removal of cam-shafts
      Installation of cam-shafts
      Check of axial shift of cam-shafts
      Marking of cam-shafts
      Replacement of maslosjemny caps
      Check of directing plugs of valves
      Processing of saddles of valves
      Sizes of valves
      Check of pistons, piston rings and diameter of the cylinder
   + Mechanical part (petrol engines 4,2L)
   + Mechanical part (diesel engines 5,0L)
   + Removal and stretcher installation
   + pressurization System (diesel engines)
   + cooling System (petrol engines)
   + cooling System (diesel engines)
   + greasing System (petrol engines)
   + greasing System (diesel engines)
   + injection System (petrol engines)
   + injection System (diesel engines)
   + System of production of the fulfilled gases
   + System топливоподачи (beninovy engines)
   + Tables
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes



Volkswagen Touareg / Touareg repair>> Engine>> Mechanical part (petrol engines 3,2L)>> Removal and installation of the left and right pillows of a support of the engine
Removal
Remove the air filter assembled with an air flowmeter.
Turn off fixing nuts 2 on the right and left pillows of the engine.

Fig. 2.39 . Adapter installation


To insert in a traverse 10-222A the adapter / the high party directing for the running screw up, as is shown in drawing 2.39 .
After that insert adapters / in a traverse 10-222A on the right and at the left. Establish to a traverse 10-222A on longerons.

Fig. 2.40 . Engine installation on a traverse


Pick up the engine two earrings / to adapters / and slightly to pull its (fig. 2.40) .
Then unscrew fixing bolts 1 of the left and right pillow of an engine / stretcher.
If necessary to use free space between GBTs and a forward wall.
Now accurately raise the engine by means of the crane/.
For removal of pillows of the engine it is necessary to turn off in addition fastening of the right or left support of the engine from the block of cylinders as the engine while cannot be lifted rather highly.

Fig. 2.41 . Scheme of installation of sealing flanges: 1–bolt; 2–damper of krutilny fluctuations; 3–bolt; 4–epiploon; 5–sealing flange; 6–block of cylinders; 7–sealing flange; 8–epiploon; 9–two-mass flywheel; 10-bolt; 11-bolt


Installation
Installation is carried out in return sequence.
At installation check the correct landing of a pin of a pillow of the engine in a support.
At first acquire all fixing bolts by hand, only then tighten them with the ordered moment of an inhaling.
Moment of an inhaling of a fixing bolt 1: 60 N · m.
Moment of an inhaling of a fixing bolt 2: 75 N · m.
The moment of an inhaling of fixing bolts of the case oil engine filters/support on the left block of cylinders: 23 N · m.
The moment of an inhaling of fixing bolts of a support of the engine on the right block of cylinders: 40 N · m.



<