VW Touareg repair


+ 1. Operation and car maintenance
- 2. Engine
   + Preliminary checks on the car
   - Mechanical part (petrol engines 3,2L)
      Removal of the power unit
      Removal and installation of the left and right pillows of a support of the engine
      Removal and installation of a conducted disk
      Removal and epiploon installation from a flywheel
      Replacement of an epiploon of a cranked shaft on the party of a damper of krutilny fluctuations
      Replacement of a sealing flange of a cranked shaft on the party of a damper of krutilny fluctuations
      Removal and installation of a cranked shaft
      Removal and installation of a lateral cover
      Removal and installation of a cover of a head of the block of cylinders
      Removal and installation of a head of the block of cylinders
      Check of phases of a gazoraspredeleniye
      Adjustment of phases of a gazoraspredeleniye
      Removal of cam-shafts
      Installation of cam-shafts
      Check of axial shift of cam-shafts
      Marking of cam-shafts
      Replacement of maslosjemny caps
      Check of directing plugs of valves
      Processing of saddles of valves
      Sizes of valves
      Check of pistons, piston rings and diameter of the cylinder
   + Mechanical part (petrol engines 4,2L)
   + Mechanical part (diesel engines 5,0L)
   + Removal and stretcher installation
   + pressurization System (diesel engines)
   + cooling System (petrol engines)
   + cooling System (diesel engines)
   + greasing System (petrol engines)
   + greasing System (diesel engines)
   + injection System (petrol engines)
   + injection System (diesel engines)
   + System of production of the fulfilled gases
   + System топливоподачи (beninovy engines)
   + Tables
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes



Volkswagen Touareg / Touareg repair>> Engine>> Mechanical part (petrol engines 3,2L)>> Check of phases of a gazoraspredeleniye
NOTE
Phases of a gazoraspredeleniye can be checked at the established engine.

Procedure for test
Remove an inlet collector and a cover of a head of the block of cylinders.
To remove a forward noise isolation.

Fig. 2.58 . Installation 1 цил. in situation VMT


Translate the crankshaft by means of a fixing bolt of a damper of krutilny fluctuations in the direction of rotation of the engine to VMT mark цил. 1 (fig. 2.58) .
The ruler for cam-shafts of T10068 A should enter in both flutes.
If to enclose a ruler for cam-shafts it is not possible, once again turn the crankshaft in the direction of rotation of the engine.

NOTE
If the ruler for T10068 A cam-shafts still does not enter, turn the crankshaft in the direction of rotation of the engine approximately on 5 mm above situation VMT цил. 1 (depends on admissions of chains of a drive of GRM).

Compare adjusting marks of phase shifters to marks in a cover of the distributive mechanism.

Fig. 2.69 . Combination of labels on phase shifters with notches of a cover of the distributive mechanism


Marks A and B in phase shifters should coincide with notches of a cover of the distributive mechanism C (fig. 2.69) .
The distance between tooth 1 and tooth of 2 asterisks of phase shifters should make in accuracy of 16 rollers of a chain.

NOTE
In drawing 2.69 the system of adjustment of phases of a gazoraspredeleniye is shown at the removed cover.

If marks do not coincide adjust gazoraspredeleniye phases.
If marks coincide establish a cover of a head of the block of cylinders and an inlet collector.


<