VW Touareg repair


+ 1. Operation and car maintenance
- 2. Engine
   + Preliminary checks on the car
   - Mechanical part (petrol engines 3,2L)
      Removal of the power unit
      Removal and installation of the left and right pillows of a support of the engine
      Removal and installation of a conducted disk
      Removal and epiploon installation from a flywheel
      Replacement of an epiploon of a cranked shaft on the party of a damper of krutilny fluctuations
      Replacement of a sealing flange of a cranked shaft on the party of a damper of krutilny fluctuations
      Removal and installation of a cranked shaft
      Removal and installation of a lateral cover
      Removal and installation of a cover of a head of the block of cylinders
      Removal and installation of a head of the block of cylinders
      Check of phases of a gazoraspredeleniye
      Adjustment of phases of a gazoraspredeleniye
      Removal of cam-shafts
      Installation of cam-shafts
      Check of axial shift of cam-shafts
      Marking of cam-shafts
      Replacement of maslosjemny caps
      Check of directing plugs of valves
      Processing of saddles of valves
      Sizes of valves
      Check of pistons, piston rings and diameter of the cylinder
   + Mechanical part (petrol engines 4,2L)
   + Mechanical part (diesel engines 5,0L)
   + Removal and stretcher installation
   + pressurization System (diesel engines)
   + cooling System (petrol engines)
   + cooling System (diesel engines)
   + greasing System (petrol engines)
   + greasing System (diesel engines)
   + injection System (petrol engines)
   + injection System (diesel engines)
   + System of production of the fulfilled gases
   + System топливоподачи (beninovy engines)
   + Tables
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes

ATola -

Volkswagen Touareg / Touareg repair>> Engine>> Mechanical part (petrol engines 3,2L)>> Replacement of an epiploon of a cranked shaft on the party of a damper of krutilny fluctuations
NOTE
If the plastic sealing flange is established, the epiploon separately is not replaced – the sealing flange should be replaced.

Removal
Bring a radiator frame into service situation.
Remove poliklinovy a belt.
Remove a damper of krutilny fluctuations. For this purpose fix a damper of krutilny fluctuations by means of a key for T10069 fixing.

Fig. 2.48 . Hook installation under a working edge of an epiploon


Insert T20143/1 hook, as is shown in drawing 2.48 , under a working edge of an epiploon.
To Oboprita a hook – T20143/1 – on a flange, hook an epiploon in the direction of an arrow and remove it.

Installation
Remove the oil remains on мыске a cranked shaft with pure rags.
Get directing plug 1 (T10215/1) in front on мысок the crankshaft.
Then accurately get an epiploon 2 over the directing plug as it is possible more deeply.

Fig. 2.49 . Order of a press fitting of details


Against the stop press an epiploon by means of an opravka of 3 (T10215/2). For this purpose use an old fixing bolt 4 dampers of krutilny fluctuations (fig. 2.49) .

NOTE
It is necessary to replace a fixing bolt of a damper of krutilny fluctuations.

Tighten a fixing bolt by means of a dinamometrichesky key of V.A.G 1601.
Establish a damper of krutilny fluctuations and fix it a key for T10069 fixing.
Tighten a new fixing bolt with the moment of an inhaling of 100 N · m + 1/4 turns (90 °).
Establish poliklinovy a belt.


<