VW Touareg repair


+ 1. Operation and car maintenance
- 2. Engine
   + Preliminary checks on the car
   - Mechanical part (petrol engines 3,2L)
      Removal of the power unit
      Removal and installation of the left and right pillows of a support of the engine
      Removal and installation of a conducted disk
      Removal and epiploon installation from a flywheel
      Replacement of an epiploon of a cranked shaft on the party of a damper of krutilny fluctuations
      Replacement of a sealing flange of a cranked shaft on the party of a damper of krutilny fluctuations
      Removal and installation of a cranked shaft
      Removal and installation of a lateral cover
      Removal and installation of a cover of a head of the block of cylinders
      Removal and installation of a head of the block of cylinders
      Check of phases of a gazoraspredeleniye
      Adjustment of phases of a gazoraspredeleniye
      Removal of cam-shafts
      Installation of cam-shafts
      Check of axial shift of cam-shafts
      Marking of cam-shafts
      Replacement of maslosjemny caps
      Check of directing plugs of valves
      Processing of saddles of valves
      Sizes of valves
      Check of pistons, piston rings and diameter of the cylinder
   + Mechanical part (petrol engines 4,2L)
   + Mechanical part (diesel engines 5,0L)
   + Removal and stretcher installation
   + pressurization System (diesel engines)
   + cooling System (petrol engines)
   + cooling System (diesel engines)
   + greasing System (petrol engines)
   + greasing System (diesel engines)
   + injection System (petrol engines)
   + injection System (diesel engines)
   + System of production of the fulfilled gases
   + System топливоподачи (beninovy engines)
   + Tables
+ 3. Transmission
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes

: best connections

Volkswagen Touareg / Touareg repair>> Engine>> Mechanical part (petrol engines 3,2L)>> Adjustment of phases of a gazoraspredeleniye
NOTE
Establish chains of a drive of GRM. These assembly operations can be executed only on the removed engine

Works order

ATTENTION
At any installation works, in particular in a motor compartment because of dense configuration, it is necessary to consider the following:
– (for example fuel, hydraulic, an absorber with absorbent carbon, systems of cooling, central air contour, pipelines of brake system, vacuum hoses), and also electric wires it is necessary to lay highways of all types how they were laid initially. Provide free space for all mobile and hot components.

NOTE
Chains of a drive of cam-shafts can be removed only at the removed engine. The following operations begin at the disassembled engine. Thus, there is a possibility to begin adjustment from the corresponding place depending on that, the engine is how disassembled.

Establish a roller chain and a natyazhitel of a chain of an intermediate shaft with a tension level.

Fig. 2.70 . Combination of tooth of an asterisk with a bearing joint «cylinder 1 VMT»


Adjust position of the crankshaft in relation to an intermediate shaft. For this purpose ground tooth of a leading asterisk of B should coincide with a bearing joint of «cylinder 1 VMT» (fig. 2.70) .
Establish both bolts without fillets for fastening of a directing level 2 and tighten them the moment of 10 N · m.

NOTE
If the roller chain was already used earlier, it is necessary to take into consideration the specified direction of rotation.

Establish directing level 2 with a roller chain 1 and both asterisks of a chain 3 and 4. The mark in an asterisk of the 4th roller chain should settle down coaxially with a notch of C or D on an adjusting washer of an intermediate shaft (fig. 2.70) .
At installation it is necessary to track that the roller moved in a directing level from the crankshaft to an intermediate shaft without any sagging.
Manually screw asterisks of a chain 3 and 4 on an intermediate shaft.

NOTE
Pay attention to need of replacement of all bolts of fastening of asterisks.

Establish on the opposite side a natyazhitel of a chain.
Unblock blocking gear gearing of a natyazhitel of a chain of A by means of a small screw-driver and press a tension level to a natyazhitel of a chain.
In this situation establish a natyazhitel of a chain and to fasten it the moment of 8 N · m.
Fix a damper of krutilny fluctuations by means of a key for T10069 fixing.
Tighten a new fixing bolt of asterisks 3 and 4 for a chain drive of an intermediate shaft with the moment of an inhaling of 60 N · m + 1/4 about. (90 °).
Remove T10069 countersupport.
Once again check position of the crankshaft B in relation to an intermediate shaft C or D (fig. 2.70) .
Again bring the engine into situation VMT цил. 1.
Establish a roller chain of a drive of a cam-shaft.
Bring the established cam-shafts into GBTs in situation VMT цил. 1.

NOTE
If necessary turn cam-shafts a wrench 32 in the correct situation.
The ruler for cam-shafts of T10068 A should not be thus enclosed in flutes.




<