VW Touareg repair


+ 1. Operation and car maintenance
+ 2. Engine
- 3. Transmission
   + 6-step automatic transmission 09D
   - Hydrotransformer check
      Liquid pumping from the hydrotransformer
      Hydrotransformer installation
      Repair of a drive of gear shifting
      Removal and installation of the handle of the selector
      Check and adjustment of draft of the selector
      Removal and installation of draft of the selector
      Removal and slip installation
      Removal and frame installation
      Removal and installation of an electromagnet of blocking of the N110 selector
      Removal and installation of the switch of the selector (the lever is blocked in the situation "P") F319
      Removal and installation of a drive of gear shifting
      Removal and transmission installation, cars with the diesel R5 engine
      Removal and transmission installation, cars with petrol V6 and V8 engines, turbodiesel engines V6 TDI, V10 TDI and the petrol W12 engine
      Inhaling moments
      Removal and installation of highways and ATF radiator
      Removal and installation of the control unit of an automatic transmission of J217
      Replacement of a sealing ring of a secondary shaft
      Removal and installation of the oil pallet
      Removal and installation of the mesh oil filter
      Removal and installation of the sensor of pressure for hydrosystem 1 in AKP G193 and the pressure sensor for hydrosystem 2 in AKP G194
      Removal and installation of a zolotnikovy box
      Removal, installation and adjustment of the multipurpose F125 switch
   + Mechanical transmission 08D and transfer case Е473
   + Driveshaft
   + Driving mechanism
   + Tables
+ 4. Running gear
+ 5. Steering mechanism
+ 6. Brake system
+ 7. Onboard electric equipment
+ 8. Body
+ electric equipment Schemes



Volkswagen Touareg / Touareg repair>> Transmission>> Hydrotransformer check>> Check and adjustment of draft of the selector
Check
Switch the selector in the situation "P".
Remove a noise isolation under a transmission.

Fig. 3.11 . Draft of the selector


Disconnect draft of the selector 2 from a lever/rod of a choice of transfers (fig. 3.11) .
Switch the selector from the situation "P" in the situation "S".
Thus draft of the selector and a drive of gear shifting should have an easy course, otherwise, replace draft of the selector or a gear shifting drive.
Switch the selector in the situation "P".
Establish a lever/rod of a choice of transfers on a transmission in the situation "P". The lever should enter into gearing with a wheel of parking blocking, forward wheels are blocked (cannot turn in one direction at the same time).
Draft of the selector should press a lever / rod of a choice of transfers, otherwise adjust draft of the selector.
Carefully press draft of the selector for a lever / rod of a choice of transfers. Thus do not bend a lever/rod of a choice of transfers, otherwise it will be precisely impossible to adjust gear shifting.
Adjust draft of the selector.

Setup of the lever
Disconnect draft of the selector from a lever / rod of a choice of transfers.
Switch the selector in the situation "S".
Establish a lever / rod of a choice of transfers on a transmission in situation "D".
Remove the handle of the lever of the selector.
It is necessary to observe sequence of shutdown of joint stock bank surely.
Disconnect the mass plug from joint stock bank at the switched-off ignition.
Remove an ashtray and a cover of a drive of gear shifting from the central console.
Remove an overlay of a drive of gear shifting.
Remove a frame from a gear shifting drive.
Turn off tightening a bolt of draft of the selector approximately on one turn.
Carefully press draft of the selector for a lever/rod of a choice of transfers so that not to bend a lever/rod of a choice of transfers, otherwise gear shifting it will be precisely impossible to adjust.
Define position of the selector, for this purpose slightly shake the selector in situation "D" forward-back, without switching from situation "D".

Fig. 3.12 . A tightening of a tightening bolt by means of a nozzle


Tighten in this situation tightening a bolt with the moment of 10 N · m. For this purpose it is possible use T40031 nozzle (fig. 3.12) .
Further installation is carried out in return sequence.
Establish an ashtray and a cover of a drive of switching of the central console.
Connect joint stock bank.
To carry out working operations after joint stock bank connection.


<